1、接通電源后，查看指示燈是否正常，如果指示燈為紅色把三項火線其中兩項線頭調整一下，如果顯示綠燈為正常。

1, after the power supply, check the indicator light is normal, if the indicator light is red, three items of FireWire, two thread adjustments, if the green light is normal.

2、開機前設定溫度，防盜門 鋼質門一般溫度為246-256度，鋼板門溫度為210-220度，轉印時間設定鋼木門為2-3分鐘，防盜門為4-5分鐘，鋼板門為12-16分鐘。

2, before setting up the temperature, anti-theft door steel door general temperature is 246-256 degrees, steel door temperature is 210-220 degrees, transfer time set steel door for 2-3 minutes, anti-theft door for 4-5 minutes, steel door for 12-16 minutes.

3、正常工作先預熱機器，必須先抽真空，然后工作臺推到加熱倉里面進行幾分鐘的加熱（切記一定抽真空預熱，否則損壞硅膠模具）。正常工作發現轉印工件木紋不清晰，是因?yàn)闇囟鹊突驎r間短造成的。把溫度適當提高5-10度或時間延長20-30秒。

3, the normal work to preheat the machine, you must first vacuum, and then push the work station to the heating chamber inside for a few minutes heating (remember to vacuum preheating, otherwise damage silicone mold). Normal work has shown that the graining of the workpiece is not clear because of low temperature or short time. Increase the temperature by 5-10 degrees or 20-30 seconds longer.

4、真空壓力表調整為低壓0.8Mpa，高壓1.2Mpa為正常。

4. Vacuum pressure gauge is adjusted to low voltage 0.8Mpa, high voltage 1.2Mpa is normal.

5、轉印機每1-2個月?lián)Q一次真空泵油，經常檢查油的液面。

5, transfer machine every 1-2 months for a vacuum pump oil, often check the oil level.

6、新設備使用1-2天后應檢查各個接線頭是否松動擰緊各接線（擰緊電器箱電器接線，加熱管連接線）。

6, the use of new equipment 1-2 days later, should check the wiring head is loose, tighten the wiring (tighten the electrical box, electrical wiring, heating pipe connection line).

7、真空罐設有放水閥，如果設備處在潮濕環境中，真空罐應隔幾天排放一下水。

7. The vacuum tank is equipped with a drain valve. If the equipment is in a humid environment, the vacuum tank should be discharged every few days.

8、新設備或新更換的硅膠板，在使用幾天后，正常工作中如果出現橫豎皺折，應立即停止使用，調整硅膠板松緊度，否則嚴重?fù)p壞硅膠板。

Silica gel plate 8, new equipment or new replacement, in the use of a few days later, the normal work if the horizontal fold, should immediately stop using, adjust the tightness of the silica gel plate, otherwise severely damaged silicon sheet.

9、下班后先關掉急停開關，切斷電源。

9, after work, turn off the emergency stop switch first, cut off the power supply.